a5e4f70f

22:24. Central console

Removal
Fig. 16-48. Central console: 1 – left overlay of the central console; 2, 4, 6, 8, 18, 20, 21 – bolts, 2,5 N · m; 3 – screw, 2,5 N · m; 5 – ashtray; 7 – central section of the dashboard; 9 – cap; 10 – tightening bolt, 1 N · m; 11 – handle of the lever of the parking brake; 12 – washer; 13 – decorative slip; 14 – finishing of the parking brake; 15 – back ventilating grate; 16 – decorative overlay of the panel of a back ventilating grate; 17 – bolt, 1,5 N · m; 19 – central console

Fig. 16-49. Device from a wire with a diameter of 3 mm for dismantle of a ventilating grate from the central section of the dashboard: X = 6 mm

Manufacture of a steel wire with a diameter of 3 mm the device for dismantle of a ventilating grate from the central section of the dashboard (fig. 16-49).
Remove the holder of phone.
Move front seats against the stop back.
Remove a carpet from two parties of the central console.
Turn an accelerator pedal on 90 ° counterclockwise.
Fig. 16-50. Arrangement of bolts (1, 2) of fastening of the left finishing (3) central consoles

Unscrew bolts 1 and 2 fastenings of the left upholstery of the central console (fig. 16-50).
Remove the left finishing from the central console for what move it forward and disconnect a back part of an upholstery.
Fig. 16-51. Arrangement of bolts (2, 3) of fastening of the right finishing (1) of the central console

Unscrew bolts 2 and 3 fastenings of the right finishing of the central console (fig. 16-51). Access to forward bolts opens after removal of a carpet of a floor.
Remove the right finishing from the central console for what move it forward and disconnect a back part of an upholstery.
Fig. 16-52. Arrangement of a clamp (1) of the handle (2) levers of the parking brake

Lift, as far as possible, up the handle of the parking brake. Press a clamp of 1 (fig. 16-52) of the handle 2 levers of the parking brake down and, having pulled, remove the handle from the lever.
Fig. 16-53. Arrangement of a cap (1) of a tightening bolt and decorative slip (2) upholsteries of the lever of the parking brake

Using a screw-driver edge as the lever, remove a decorative overlay of 2 (fig. 16-53) from finishing of the lever of the parking brake.
Remove a cap, weaken on two turns tightening a bolt and, moving forward, release a latch in a back part, remove finishing of the lever of the parking brake (see fig. 16-53).
On cars with the mechanical transmission unscrew the handle from the lever of gear shifting and include the fourth transfer. 
Remove the central armrest.
Fig. 16-54. Arrangement of a back ventilating grate (1), screws (3) and decorative slip (2)

Remove a decorative overlay of the panel of a back ventilating grate (fig. 16-54).
Turn out two screws 3 and remove a ventilating grate from a back part of the central console.
Fig. 16-55. Use of adaptation from a wire (1) installed in openings (2) for removal of a ventilating grate from the central section of the dashboard

Fix adaptation from a wire through a ventilating grate in openings of the case of a ventilating grate of the central section of the dashboard (fig. 16-55). Accurately take a ventilating grate from the central section of the dashboard.
Fig. 16-56. An arrangement of screws of fastening of the central section to the dashboard

Unscrew five screws and take the central section from the dashboard (fig. 16-56).
Disconnect electric sockets and remove the central section of the dashboard.
Fig. 16-57. Arrangement of bolts (1) of fastening of the central console (2) and bolt (4) fastenings of an ashtray (3)

Unscrew bolts of 4 (fig. 16-57) and, moving forward, remove an ashtray 3 from the central console 2.
Unscrew bolts of 1 fastening of the central console; shifting and raising a back part of the console forward, remove it on the lever of the parking brake.

Installation
Installation is carried out to the sequences, the return to removal.