a5e4f70f чернослив - купить оптом в москве Недорогие цены за.
Смотрите на сайте кирпич огнеупорный пермь.

7.7. Accelerator cable

Removal
Remove the lower casing of the panel from the driver.
Take in deepening for the driver's legs a transitional cap from a partition of a motor compartment.

Fig. 4.1-15. Removal of a cable (1) of an accelerator from the top part of a pedal (2) accelerators



Disconnect an accelerator cable from the top part of a pedal of an accelerator (fig. 4.1-15)

Cars with the automatic transmission
Disconnect the electric socket from the mechanism of compulsory inclusion of a low gear.
Remove the protection covers located in the left back part of a motor compartment.

Fig. 4.1-16. Arrangement of screws of fastening of a casing of the six-cylinder engine



Unscrew four screws and remove an engine casing (fig. 4.1-16; 4.1–17).

Fig. 4.1-17. Arrangement of screws of fastening of a casing of the eight-cylinder engine




Cars about a cruise control

Fig. 4.1-18. Arrangement of a vacuum hose (2) and bolts (1) of fastening of the vacuum chamber of system cruise control



Disconnect a vacuum hose 2 from the vacuum chamber of system a cruise control (fig. 4.1-18).
Unscrew two bolts and remove from an arm the vacuum chamber of system a cruise control.

Cars with six-cylinder engines

Fig. 4.1-19. Fastening of a cable of an accelerator to the lever of the drive of a butterfly valve of cars with six-cylinder engines: 1 – accelerator cable tip; 2 – arm; 3 – spring clip; 4 – rubber plug of a cover of a cable of an accelerator; 5 – spring clamp


Using a rozhkovy key on 8 mm, disconnect a tip of a cable of 1 accelerator from the lever of the drive of a butterfly valve (fig. 4.1-19).
Take a spring clip 3 fastenings of a cover of a cable of an accelerator to an arm 2 and take a cable from an arm 2.
Using a screw-driver edge as the lever, remove a spring clamp 5.
Extend an accelerator cable in a motor compartment.

Cars with eight-cylinder engines

Fig. 4.1-20. Fastening of a tip of a cable of an accelerator (1) to the lever (2) drives of a butterfly valve



Disconnect an accelerator cable tip from the lever of the drive of a butterfly valve (fig. 4.1-20).

Fig. 4.1-21. Fastening of a cable of an accelerator on cars with six-cylinder engines: 1 – rubber plug; 2 – spring clip; 3 – arm; 4 – accelerator cable cover



Take out a spring clip of 2 (fig. 4.1-21) and the rubber plug 1 with a cable cover 4 accelerators from an arm 3.
Extend an accelerator cable in a motor compartment.

Fig. 4.1-22. Air filter: 1 – air duct; 2 – G70 air consumption measuring instrument; 3 – collar; 4 – inlet air duct; 5 – collar; 6 – the soaking-up air duct; 7 – nut; 8 – rubber pillow; 9 – the filtering element of the air filter; 10 – case of the air filter; 11, 12 – an air duct


Fig. 4.1-23. The fuel highway with nozzles: 1 – a fuel supply tube from the fuel filter; 2 – fuel return tube; 3 – bolt, 10 N · m; 4 – spring connector; 5 – sealing rings; 6 – fuel pressure regulator; 7 – fuel highway; 8 – spring connector; 9 – sealing ring; 10 – nozzle; 11 – sealing ring; 12 – inlet collector


Fig. 4.1-24. Throttle knot and system of switching of an inlet collector: 1 – top part of an inlet collector; 2 – bolt, 10 N · m; 3 – bolt, 20 N · m; 4 – laying; 5 – valve of stabilization of idling N71; 6 – bolt, 10 N · m; 7 – bolt, 6 N · m; 8 – flange; 9 – basis of an inlet collector; 10 – laying; 11 – bolt, 10 N · m; 12 – vacuum chamber of the valve of switching of an inlet collector; 13 – bolt, 20 N · m; 14 – throttle knot; 15 – laying; 16 – bolt, 20 N · m; 17 – the mechanical valve of system of recirculation of the fulfilled gases (EGR); 18 – EGR G98 temperature sensor; 19 – bolt, 10 N · m; 20 – laying; 21 – bolt, 10 N · m



Installation
Installation is carried out to the sequences, the return to removal.
Do not carry too far an accelerator cable.
Adjust an accelerator cable.
Adjustment of a cable of an accelerator
The help of the second mechanic is necessary for adjustment of provision of a cable of an accelerator.
Take out a spring clip and the rubber plug with an accelerator cable cover from an arm.
Press an accelerator pedal against the stop and adjust the provision of a cable of an accelerator so that the butterfly valve was completely open. The provision of a cable of an accelerator is regulated by movement of the rubber plug on a cable cover. In this situation insert the rubber plug of a cover and fix it by a spring clip.

Note
At installation it is necessary to use new sealing rings and laying.